Because what the world needs most is one more pin cushion tutorial.
Previously: I made a giant, enormous, humongous, monster pin cushion because the house elves like to steal my store-bought tiny-tomato-looking one. Also, I have a ton of scraps, a bunch of polyfil, and a need to store my glass-head silk pins in something other than a glass jar. Oh, glass jars are wonderful (I have previously confessed to having an abundance of them), but when I reach in a glass jar to get a pin, most often I get blood instead when I stick myself with a pin. Occasionally the blood is accompanied by a pin stuck in my finger (or more notably, under my fingernail).
Clearly, the amazing usefulness of a glass jar is limited.
So I made a honker of a pin cushion. I’m making another one for my mother because she was mightily jealous of the utter usefulness, the awesome size, and even the amazing aesthetics of my big ol’ pin cushion.
In short, she had a severe case of pin cushion envy.
What’s a good daughter to do? Make her mama a giant pin cushion! Here’s how I did it. If you do it, let me know. I’d love to hear from you and see pictures of your creation.
Before I tell you how to make it, I should tell you some other things about the pin cushion:
I created the pin cushion so that you can make the entire thing from a single fat quarter (assuming that the fat quarter was cut properly and is a true 18” x 21”).
Instead of using a single fat quarter, I used four different fabric swatches from my Painted Flowers collection: I used the Large Flowers on Blue and White for the top; the Large Flowers on Blue for the bottom; the Flowers on Blue and White for two sides; and the Flowers on Blue for the other two sides.
This would be a good project to use up some jelly roll scraps. Three jelly roll scraps sewn together will give you a 6.5” wide top and bottom. And the sides are already 2.5”. So with a few leftovers, you’re set. You would need ten 6.5″ long strips to make the whole thing: three for the top, three for the bottom, and one for each side.
All seam allowances are 1/4 inch.
I like to press each seam with right sides together just after sewing because I think it produces a better seam once it’s turned and stuffed. (I’ve heard this called “setting the seam”.) But YMMV, so you don’t have to do this.
I didn’t prewash this fabric. For most sewing projects, I prewash fabric. I don’t prewash when I’m sewing something to be stuffed. Stuffing fabric stretches it slightly; when you prewash, it stretches it slightly more. Again, YMMV, so you can prewash if you want.
I don’t clip corners when I stuff something unless I’m stuffing something really, really small with an acute, tight corner. Stuffing fabric stretches it; when you clip corners you can pop through the seams when you’re in a corner if you’ve clipped them too close to the seam.
I fray checked the edges. I like to do that when I’m making something that could get a lot of wear and/or is going to be stuffed tight. Relax; that smell will go away in a week or so.
Finally, here’s how you make it.
A fat quarter of fabric
A bunch of polyfil
Two enormous buttons (mine are 1 3/8” (34mm))
A tag (optional)
1. Cut out your fabric:
6.5” x 6.5” for the top
6.5” x 6.5” for the bottom
Four 6.5” x 2.5” for the sides
2. Right sides together, sew one side to the top without sewing the beginning and end 1/4” of the side strip. I marked the top and bottom corners 1/4 inch away from the edges, but you can eyeball it if you’re good and/or daring.
3. Repeat step 2 for the remaining three sides. For these last three sides, you have to bend back the previous sewn side so that you don’t sew over it again. In the pic below, you can see how I bent back the adjacent two sides so that I could sew the last side to the top. The fray check actually helps with this because it makes the edges a little stiff and able to hold a bend.
Side Note: If I were reading these instructions, it’s at about this time that I would wonder why the instructions didn’t have me connect the four sides to each other and then connect them in a loop to the top. You might have wondered the same. So I’ll tell you.
The big red monster pin cushion at the top is my second attempt to make a giant pin cushion. In the first attempt, I attached the sides (in one long strip) to the top and bottom. After stuffing the cushion, I didn’t have a block with rectangles for sides; I had a block with parallelograms for sides. I don’t know what happened. I suspect that I didn’t sew the bottom fabric in the same place I sewed the top fabric. So I ended up with the top and bottom planes parallel without matching the corners. Also, I suspect house elf sabotage. I have no other excuses.
Anyway. On my second attempt, using the method I’m describing here, I got it right.
4. Right sides together, sew the bottom and one side together. (Don’t sew the sides together!)
5. Repeat step 4 for the other 3 sides. (Still haven’t connected the sides to each other…)
6. If you’re adding a tag, now’s the time to insert it on one of the open sides. (If not, skip this step.) Make sure it’s inside the whole fabric bundle where the right sides are all together. I glued mine in place on the edge.
7. Now sew three of the sides together, making sure that one of the sides you’re sewing has a tag if you’re using one. Sew from and to the ends of the seams you sewed when you attached the sides to the top and bottom. You should have an inside-out block with one side open, one tag on the inside, and three sides sewn.
8. Turn it so the right sides are outside and stuff it tightly. Make sure that you turn the corners tightly so you can get a nice square block. Also, it helps to have a poker to poke the stuffing in the corners. My poker came with a bag of polyfil; it’s just a long wood rod with one pointy end.
9. Close the opening by hand. I used a hidden stitch. Here’s a good tutorial for it at Taffy Talk called an invisible closing seam.
10. With a big honkin’ needle and button thread, attach the buttons to the center of the top and bottom. You want to go through the entire pin cushion with the thread so that the two buttons are connected
Pull the thread tightly to make the pin cushion appear tufted. Hide the knot under a button and hide the tail of the thread inside the cushion as explained in the invisible closing seam tutorial I linked to above.
11. Embellish if desired. I’m considering embroidering a fly stitch along the top seams. If I do, I’ll post update pics later on. I don’t know; I love it as is.
Finished measurements: 6” x 6” x 2”.
I hope you like the tutorial and I hope you use it. Really, it’ll take you longer to read this monster tutorial than it will to make the monster pin cushion.